Standalone Management: Difference between revisions

Revision as of 22:01, 13 January 2025

General Setup

Crank sensor

07k crank sensor with plug

The 07K engine uses a Hall Effect crank position sensor. This is synced with the cam sensor for Dual Wheel Missing Tooth engine operation and VVT.

On the rear of the sensor plug the wires are numbered 1 through 3.

Pin 1: Sensor output.

Pin 2: Sensor ground.

Pin 3: 5v.

07k vs 1.8t crank sensor comparison

For best results this sensor should shielded and kept away from sources of EMI like the starter, high-current wires, and any noise source.

Incorrect wiring diagrams

This sensor is easily confused with the similar-looking 1.8t Variable-Reluctance(VR). Both are three-wire sensors, The 07k uses two small hex bolts and the 1.8t uses a single bolt. In the wiring diagrams of both the 1.8t and the B series of engines (BGP, BGQ, BPS) have the same sensor diagram but use different sensors. Per the diagram, both show the 3-wire VR sensor with VR+, VR-, and shield ground, this is incorrect for the 07k. The C series of engines (CBTA, etc.) does not display a diagram for the sensor.

Cam Sensor

The 07k uses a single Hall effect sensor on the intake cam. This is synced with the crank sensor for Dual Wheel Missing Tooth engine operation and VVT.

07k Cam sensor

On the rear of the sensor plug the wires are numbered 1 through 3.

Pin 1: Sensor ground.

Pin 2: Sensor output.

Pin 3: 5v.

For best results this sensor should shielded and kept away from sources of EMI like the starter, high-current wires, and any noise source.

Coil On Plug(COP)

Coolant sensor

2 Wire

3 Wire

Knock Sensor(s)

Throttle body

Map sensor

Mega squirt 3X

**Please note that this is a work in progress, tune and wire at your own risk**

Coil on plug(COP)

Wiring diagram for COP^[1]

MS3X ignition output modification circuit^[2]

Megasquirt VAG COP driver on a PCB^[3]

Drive by cable

Using a VR6 Throttle body

Wiring diagram

Male 8 pin plug going into to throttle body

MS3X 2 wire PWM idle circuit ^[4]

Helpful links

@@ Line 2: / Line 2: @@
 === Crank sensor ===
-The 07K engine uses a Hall Effect crank position sensor.
+[[File:07k crank sensor.jpg|thumb|07k crank sensor with plug]]
+The 07K engine uses a Hall Effect crank position sensor. This is synced with the cam sensor for Dual Wheel Missing Tooth engine operation and VVT.
+On the rear of the sensor plug the wires are numbered 1 through 3.
+'''Pin 1: Sensor output.'''
+'''Pin 2: Sensor ground.'''
-This sensor is easily confused with the similar-looking 1.8t Variable-Reluctance(VR). Both are three-wire sensors, The 07k uses two small hex bolts and the 1.8t uses a single bolt.
+'''Pin 3: 5v.'''
+[[File:07k vs 1.8 crank sens.png|thumb|07k vs 1.8t crank sensor comparison ]]
+For best results this sensor should shielded and kept away from sources of EMI like the starter, high-current wires, and any noise source.
+===== Incorrect wiring diagrams =====
+This sensor is easily confused with the similar-looking 1.8t Variable-Reluctance(VR). Both are three-wire sensors, The 07k uses two small hex bolts and the 1.8t uses a single bolt. In the [[Wiring Diagrams|wiring diagrams]] of both the 1.8t and the B series of engines (BGP, BGQ, BPS) have the same sensor diagram but use different sensors. Per the diagram, both show the 3-wire VR sensor with VR+, VR-, and shield ground, this is incorrect for the 07k. The C series of engines (CBTA, etc.) does not display a diagram for the sensor.
 === Cam Sensor ===
+The 07k uses a single Hall effect sensor on the intake cam. This is synced with the crank sensor for Dual Wheel Missing Tooth engine operation and VVT.
+[[File:07k Cam sensor.jpg|thumb|07k Cam sensor]]
+On the rear of the sensor plug the wires are numbered 1 through 3.
+'''Pin 1: Sensor ground.'''
+'''Pin 2: Sensor output.'''
+'''Pin 3: 5v.'''
+For best results this sensor should shielded and kept away from sources of EMI like the starter, high-current wires, and any noise source.
 === Coil On Plug(COP) ===