Standalone Management - Revision history

Vindez77: /* Throttle body Pinout[1] */

2026-08-08T20:29:28Z

Throttle body Pinout[1]

← Older revision		Revision as of 20:29, 8 August 2026
Line 59:		Line 59:
	A DBW controller can be made using Arduino or purchased (e.g., ldperformance DBW or DBWX2).		A DBW controller can be made using Arduino or purchased (e.g., ldperformance DBW or DBWX2).

	==== Throttle body Pinout~~<ref name=":0">https://www.scribd.com/document/723582011/Throttle-Guide</ref>~~ ====		==== Throttle body Pinout ====
	'''Pin 1: TPS 1'''		'''Pin 1: TPS 1'''

Line 79:		Line 79:
	I have only messed with MK5 and MK7 pedals and they had identical pin layouts. They are as follows:		I have only messed with MK5 and MK7 pedals and they had identical pin layouts. They are as follows:

	==== Accelerator Pedal Pinout<ref name=":0" /> ====		==== Accelerator Pedal Pinout<ref name=":0">https://www.scribd.com/document/723582011/Throttle-Guide</ref> ====
	'''Pin 1: 5V'''		'''Pin 1: 5V'''

Vindez77: /* Throttle body Pinout[1] */

2026-08-08T20:29:16Z

Throttle body Pinout[1]

← Older revision		Revision as of 20:29, 8 August 2026
Line 62:		Line 62:
	'''Pin 1: TPS 1'''		'''Pin 1: TPS 1'''

	'''Pin 2: ~~TPS 2~~'''		'''Pin 2: +5 Ref'''

	'''Pin 3: Motor 1 - Brown'''		'''Pin 3: Motor 1 - Brown'''

	'''Pin 4: ~~Output 5V~~'''		'''Pin 4: TPS 2'''

	'''Pin 5: Motor 2 - Lilas'''		'''Pin 5: Motor 2 - Lilas'''

Vindez77: /* Accelerator Pedal Pinout */

2026-08-08T20:14:45Z

Accelerator Pedal Pinout

← Older revision		Revision as of 20:14, 8 August 2026
Line 59:		Line 59:
	A DBW controller can be made using Arduino or purchased (e.g., ldperformance DBW or DBWX2).		A DBW controller can be made using Arduino or purchased (e.g., ldperformance DBW or DBWX2).

	==== Throttle body Pinout<ref>https://www.scribd.com/document/723582011/Throttle-Guide</ref> ====		==== Throttle body Pinout<ref name=":0">https://www.scribd.com/document/723582011/Throttle-Guide</ref> ====
	'''Pin 1: TPS 1'''		'''Pin 1: TPS 1'''

Line 79:		Line 79:
	I have only messed with MK5 and MK7 pedals and they had identical pin layouts. They are as follows:		I have only messed with MK5 and MK7 pedals and they had identical pin layouts. They are as follows:

	==== Accelerator Pedal Pinout ====		==== Accelerator Pedal Pinout<ref name=":0" /> ====
	'''Pin 1: 5V'''		'''Pin 1: 5V'''

Vindez77: /* Accelerator Pedal Pinout */

2026-08-08T20:14:27Z

Accelerator Pedal Pinout

← Older revision		Revision as of 20:14, 8 August 2026
Line 59:		Line 59:
	A DBW controller can be made using Arduino or purchased (e.g., ldperformance DBW or DBWX2).		A DBW controller can be made using Arduino or purchased (e.g., ldperformance DBW or DBWX2).

	==== Throttle body Pinout ====		==== Throttle body Pinout<ref>https://www.scribd.com/document/723582011/Throttle-Guide</ref> ====
	'''Pin 1: TPS 1'''		'''Pin 1: TPS 1'''

Line 80:		Line 80:

	==== Accelerator Pedal Pinout ====		==== Accelerator Pedal Pinout ====
	'''Pin 1: 5V'''~~<ref>https://www.scribd.com/document/723582011/Throttle-Guide</ref>~~		'''Pin 1: 5V'''

	'''Pin 2: 5V'''		'''Pin 2: 5V'''

Vindez77: /* Helpful links */

2026-08-08T20:13:49Z

Helpful links

← Older revision		Revision as of 20:13, 8 August 2026
Line 80:		Line 80:

	==== Accelerator Pedal Pinout ====		==== Accelerator Pedal Pinout ====
	'''Pin 1: 5V'''<ref>https://~~files~~.~~fueltech~~.~~net~~/~~manuals~~/Throttle~~%20Guide.pdf~~</ref>		'''Pin 1: 5V'''<ref>https://www.scribd.com/document/723582011/Throttle-Guide</ref>

	'''Pin 2: 5V'''		'''Pin 2: 5V'''

Dane944: /* VVT */

2026-04-19T01:32:24Z

VVT

← Older revision		Revision as of 01:32, 19 April 2026
Line 52:		Line 52:
	=== Coolant sensor ===		=== Coolant sensor ===
	==== 2 Wire ====		==== 2 Wire ====
	~~==== 3 Wire ====~~

	=== Knock Sensor(s) ===		=== Knock Sensor(s) ===

Dane944 at 01:29, 19 April 2026

2026-04-19T01:29:30Z

← Older revision		Revision as of 01:29, 19 April 2026
Line 156:		Line 156:


			<br clear="all">

	==== VVT Settings (EXPERIMENTAL- WIP) ====		==== VVT Settings (EXPERIMENTAL- WIP) ====

Dane944: /* Wiring */ Updated wordage in the VVT wiring and added in the pinout for the connector

2026-04-19T01:28:54Z

Wiring: Updated wordage in the VVT wiring and added in the pinout for the connector

← Older revision		Revision as of 01:28, 19 April 2026
Line 133:		Line 133:

	==== Wiring ====		==== Wiring ====
	~~The~~ VVT ~~idle~~ valve ~~wiring~~ can be found in the manual in section 3.5.4.4 (Page 47/225 MS3X/V3.57 Hardware Guide). This section has been copied below.		How to wire the VVT valve can be found in the manual in section 3.5.4.4 (Page 47/225 MS3X/V3.57 Hardware Guide). This section has been copied below.

			The diagram shows the idle valve however the same principle applies.

	<u>2-wire PWM idle valve (MS3X)</u>		<u>2-wire PWM idle valve (MS3X)</u>
Line 142:		Line 144:
	Note the diode. The MS3X mid-current outputs are configured for low-frequency valves (e.g. boost or nitrous solenoids.) For high frequency valves such as idle valves or VVT solenoids it is necessary to connect a diode from signal to 12V in the loom. Alternatively a small jumper wire can be installed inside the case to make all outputs high-frequency capable - this is detailed in the assembly section. (c) 2014-8 James Murray 2018-08-01		Note the diode. The MS3X mid-current outputs are configured for low-frequency valves (e.g. boost or nitrous solenoids.) For high frequency valves such as idle valves or VVT solenoids it is necessary to connect a diode from signal to 12V in the loom. Alternatively a small jumper wire can be installed inside the case to make all outputs high-frequency capable - this is detailed in the assembly section. (c) 2014-8 James Murray 2018-08-01

	<br clear="all">It is heavily advised to wire in the 1N4001 diode for the 07k VVT solenoid.
			<br clear="all">It is '''heavily advised''' to wire in the 1N4001 diode for the 07k VVT solenoid.
			[[File:MS3X VVT connector setup.png\|left\|thumb\|MS3X VVT Connector Pin Wiring - 12v and line to ECU]]











	==== VVT Settings (EXPERIMENTAL- WIP) ====		==== VVT Settings (EXPERIMENTAL- WIP) ====
	[[File:Ms3x VVT settings screenshot.png\|left\|thumb\|Tuner Studio MS3X VVT settings]]		[[File:Ms3x VVT settings screenshot.png\|left\|thumb\|Tuner Studio MS3X VVT settings]]

Dane944: /* VVT Timing Table (EXPERAMENTAL - WIP) */ Misspelling fix

2026-04-18T21:19:02Z

VVT Timing Table (EXPERAMENTAL - WIP): Misspelling fix

← Older revision		Revision as of 21:19, 18 April 2026
Line 143:		Line 143:

	<br clear="all">It is heavily advised to wire in the 1N4001 diode for the 07k VVT solenoid.		<br clear="all">It is heavily advised to wire in the 1N4001 diode for the 07k VVT solenoid.
	==== VVT Settings (~~EXPERAMENTAL~~ - WIP) ====		==== VVT Settings (EXPERIMENTAL- WIP) ====
	[[File:Ms3x VVT settings screenshot.png\|left\|thumb\|Tuner Studio MS3X VVT settings]]		[[File:Ms3x VVT settings screenshot.png\|left\|thumb\|Tuner Studio MS3X VVT settings]]

Line 153:		Line 153:

	<br clear="all">		<br clear="all">
	==== VVT Timing Table (~~EXPERAMENTAL~~ - WIP) ====		==== VVT Timing Table (EXPERIMENTAL- WIP) ====
	[[File:MS3x VVT table.png\|left\|thumb\|MS3X VVT Timing Table]]		[[File:MS3x VVT table.png\|left\|thumb\|MS3X VVT Timing Table]]

Dane944: /* Wiring */ notes added to the VVT wiring

2026-04-18T21:18:27Z

Wiring: notes added to the VVT wiring

← Older revision		Revision as of 21:18, 18 April 2026
Line 142:		Line 142:
	Note the diode. The MS3X mid-current outputs are configured for low-frequency valves (e.g. boost or nitrous solenoids.) For high frequency valves such as idle valves or VVT solenoids it is necessary to connect a diode from signal to 12V in the loom. Alternatively a small jumper wire can be installed inside the case to make all outputs high-frequency capable - this is detailed in the assembly section. (c) 2014-8 James Murray 2018-08-01		Note the diode. The MS3X mid-current outputs are configured for low-frequency valves (e.g. boost or nitrous solenoids.) For high frequency valves such as idle valves or VVT solenoids it is necessary to connect a diode from signal to 12V in the loom. Alternatively a small jumper wire can be installed inside the case to make all outputs high-frequency capable - this is detailed in the assembly section. (c) 2014-8 James Murray 2018-08-01

	<br clear="all">		<br clear="all">It is heavily advised to wire in the 1N4001 diode for the 07k VVT solenoid.
	==== VVT Settings (EXPERAMENTAL - WIP) ====		==== VVT Settings (EXPERAMENTAL - WIP) ====
	[[File:Ms3x VVT settings screenshot.png\|left\|thumb\|Tuner Studio MS3X VVT settings]]		[[File:Ms3x VVT settings screenshot.png\|left\|thumb\|Tuner Studio MS3X VVT settings]]